Doremi DCP to ShowVault Conversion Procedure User Manual

DCP-2K4 to ShowVault-4Conversion ProcedureDigital Cinema ServerVersion 1.2The information contained herein is confidential and may not be divulged to

4 Unit PreparationCAUTION: During the procedure presented in this document, you will have to remove screws from the unit. Make sure NOT to lose the s

5 Conversion Procedure• The lid needs to be removed. Unscrew the six screws with the Phillips screwdriver. There are two screws on each side and two

Figure 22: Screw on Motherboard: 1.0 E Dolphin• Remove the screw holding the Dolphin card on the top of the rear chassis (Figure 23).Figure 23: Screw

Figure 25: Dolphin Card Removal- 1.2 FFigure 26: Dolphin Card Removal- 1.0 E• For 1.0 E Dolphins, remove the Dolphin stand-off (Figure 27) on the moth

Figure 28: Motherboard Screw on 1.0 E Dolphin• Unplug the IDC cable from the Dolphin card (Figure 29).Figure 29: Unplugging the IDC Cable• Unplug the

Figure 31: Unplugging Ethernet Cable for the 1.2 F Dolphin• Unplug the SBC power connector cable from the Dolphin Card (Figure 32).Figure 32: Unpluggi

Figure 34: Removing the Ethernet Cable for the 1.2 F Dolphin• Tuck the SBC cable underneath the DVD and CRU, using the mounting clip underneath to hol

Figure 37: AES Card Being Removed• Unscrew the two nuts holding the card in place using the nut driver and remove the card so that the bracket looks l

Figure 41: AES Bracket in Place• Remove the DPT cover by unscrewing the screw on the motherboard, located at MH8 (Figure 42). Figure 42: Motherboard S

Figure 44:Slots After• Insert the PCI-e card provided in the PCI-e slot located on the motherboard. Push down slightly on the card until it clicks int

Table of Contents1 Introduction...

Figure 46: Dolphin Stand-off on 1.2 F DolphinFigure 47: Motherboard Screw on 1.2 F Dolphin• Remove the 1 GB RAM modules from the motherboard by pressi

Figure 49: 2G RAM Modules• Gently insert the 2GB modules into the RAM slots. Apply pressure evenly until the modules snap into place. • Place the old

5.1 Stickers• Place the ShowVault sticker provided over the DCP-2K4 sign on the front panel (Figure51).Figure 51: ShowVault Sticker in Place• Place th

Figure 53: Serial Number StickerThe hardware installation is now complete. 5.2 Assigning the Chassis Serial Number Because the Chassis Serial number f

Figure 54: About Window• Diagnostic Tool Window :◦ Go to Menu → Diagnostic Tool and check the chassis number entry as illustrated below (Figure 55):

• Select “hotfix_pcie_2GiB-1.0.0.pkg” and any licenses that appear in the Ingest window.• Click the Ingest button.• After ingesting, reboot the unit.

7 Acronyms Term DefinitionDLM Doremi License MessageDPT Dolphin Plastic TunnelIMB Integrated Media BlockPCI-e Peripheral Component Interconnect Expre

8 Document Revision HistoryDate Version Description12/01/2011 1.0 First version.03/19/2012 1.1 Minor revisions made.09/05/2012 1.2 RAM update added.

1 Introduction1.1 PurposeThis document details how to convert a DCP-2K4 to a ShowVault-4. It is presented as a step-by-step procedure that must have

2 Required Components for ConversionCAUTION: Make sure you have all the parts listed below before beginning the conversion procedure.2.1 Required To

• 3 M3 Screws (Doremi Part Number: M3x6MM-LW)Figure 5: M3 Screws• 1 Motherboard Screw (Doremi Part Number: P632x6MM-LW)Figure 6:Motherboard Screw• 1

◦ Christie (Doremi Part Number IMB-C)Figure 9: IMB Christie◦ NEC (Doremi Part Number IMB-N)Figure 10: IMB NEC• 2 RAM Modules totaling 2GB (Doremi Par

• Chassis Revision Number and Serial Number StickersFigure 12: Revision Number and Serial Number Stickers2.3 Required Accessories The following parts

Figure 15: GPIO Cable• 2 Twelve Inch Ethernet Cables (Doremi Part Number: CBL-ENET-12IN)Figure 16: Ethernet Cables• RJ45 to DB25 AES Adapter (Doremi P

3 ESD RulesESD (Electrostatic Discharge) safety rules are to be respected while assembling, repairing, or upgrading hardware on all Doremi products.