Doremi H2S-30 User Manual

H 2 S - 3 0User ManualVersion 1.4The English version of this document is the only legally binding version. Translated versions are not legally binding

2.2 Supported FormatsThe table below summarizes all supported inputs and outputs available on the H2S-30.Supported Input(s) Supported Output(s)HDMI:

3 H2S OSD Menu System OverviewThe H2S-30 is configured using the IR remote control to access the menu system through the OSD (see Section 4). Or by u

3.2 Output MenuThe Output menu can be used to set up the output parameters. See table below for more information.Sub-Menu Value DescriptionInterfaceS

Sub-Menu Value DescriptionSDI Frequency 23.98242529.9730 47.95485059.9460Match InputMatch Input x2Set the SDI output frame rate.Match Input: In this m

3.2.1 Color SpaceThe ITU-R BT.709-5 (HD formats) and ITU-R BT.601-5 (SD formats) standards define the rangeof color values in a digital signal to be:

Sub-Menu Value DescriptionInput LUT User Defined0.1 to 4.0Set the input Gamma correction.For User Defined Input LUT usethe DUIS software (see Section5

3.4 Sync MenuThe Sync menu can be used to set up the sync parameters.Sub-Menu Value DescriptionInputHDMI/DVIExternExtern: Sync is derived from the Sy

3.5 Audio MenuThe Audio menu can be used to set up the audio parameters.Sub-Menu Value DescriptionInputDVI/HDMIAudio input is set to DVI/HDMI by defa

3.6 On Screen Display (OSD) MenuThe OSD menu can be used to set up the OSD parameters.Sub-Menu Value DescriptionOSD Enable YesNoEnable or disable On

3.7 System MenuThe System menu allows access to the system parameters.Sub-Menu DescriptionSave Save current settings to flash.Select to Save, when th

Table Of Contents1 Introduction...

4 Infrared Remote ControllerThe Menu System can be accessed using the IR remote controller in conjunction with the OSD. Pressing the Menu button will

4.2 Remote Controller FunctionsRemote Control FunctionInput source selection Select: DVI-D/HDMI, or Pattern.Note: SDI and DVI-A buttons are unused“IR

4.3 Input Source Setting• To select the Input Format, press one of the buttons available in the Input Source field (see Figure 5).Figure 5: Input For

4.3.2 Setting the IR ChannelWhen using multiple H2S-30 units, you can avoid interference by pairing each unit to an individual remote. Assign each H2

5 Doremi Universal Interface Software (DUIS)5.1 DUIS InstallationTo install the Doremi Universal Interface Software, follow the steps below:• Plug t

Figure 10: ”Found New Hardware Wizard” Window Step 2• When the driver installation is complete, click on the “Finish” button (see Figure 11).Figure 11

Figure 12: Hardware Installation Warning WindowFigure 13: Hardware Installation Warning Window for Windows 7H2S.OM.001539.DRM

5.2 Doremi Universal Interface Software OverviewThe Doremi Universal Interface Software can control one or more H2S-30 devices connected to a worksta

5.3 Settings FieldThe Settings field can be used to manage the settings files.• To save the current H2S-30 configuration settings into a file, enter

• To export the settings file to a specified location, select it in the “Settings” field and click on the “Export” button. The user will be asked to c

Software License AgreementThe software license agreement can be found at the following location:http://www.doremilabs.com/support/proav-support/proav-

5.4 Tabs Description5.4.1 Input TabThe Input tab is illustrated in Figure 14 and Figure 15 above. All parameters are explained earlier in this manua

5.4.3 Image TabThe Image tab is illustrated below in Figure 17.Figure 17: H2S-30 Control Panel Image TabAll parameters are explained earlier in this

Figure 18: Gamma Correction Pop-Up WindowH2S.OM.001539.DRM Page 32 of 40

5.4.4 Sync I/O TabThe Sync I/O tab is illustrated below in Figure 19.Figure 19: H2S-30 Control Panel Sync I/O TabAll parameters are explained earlier

5.4.5 Audio TabThe Audio tab is illustrated below in Figure 20.Figure 20: H2S-30 Control Panel Audio TabAll parameters are explained earlier in this

5.4.6 OSD TabThe OSD tab is illustrated below in Figure 21.Figure 21: H2S-30 Control Panel OSD TabAll parameters are explained earlier in this manual

5.4.7 System TabThe System tab is illustrated below in Figure 22.Figure 22: H2S-30 Control Panel System TabThe parameters are explained earlier in th

• A window containing the logs will appear:Figure 23: Log Window• Select “Auto Update” from the Log Window to see all messages (see Figure 23).H2S.OM.

6 Firmware UpdateThe firmware can be updated through a USB using the DUIS. In case one of the files listed in the procedures below is missing, please

7 AcronymsTerm DefinitionDUIS Doremi Universal Interface SoftwareDVI Digital Visual InterfaceHDMI High-Definition Multimedia InterfaceHD-SDI High-Def

WARNING THIS DEVICE MUST BE GROUNDED IMPORTANTPower requirements for electrical equipment vary from area to area. Please ensure that the H2S-30 m

8 Document Revision HistoryDate Version Description02/10/2011 1.0 First version.03/02/2011 1.1 New pictures added.07/26/2012 1.2 Logo and contact inf

Protecting Yourself and the H2S-30Never touch the AC plug with wet hands. Always disconnect the H2S-30 from the power supply by pulling on the plug, n

C A U T I O NR I S K O F E L E C T R I C S H O C KD O N O T O P E N !C A U T I O N : T O R E D U C E T H E R I S K O F

1 Introduction1.1 PurposeThis document provides guidance on how to use the H2S-30 HDMI® to SDI converter that incorporates High-Definition Multimedi

2 H2S-30 Overview2.1 H2S-30 DescriptionThe H2S-30 is an HDMI to SDI format converter featuring HDMI and SDI connectors that allow for any HDMI inpu

2.1.3 H2S-30 Rear PanelThe H2S-30 rear panel is illustrated below:Figure 3: H2S-30 Rear Panel ViewThe rear panel has the following connectors:Connect