Doremi S2H-30 User Manual

S 2 H - 3 0User ManualVersion 1.4The English version of this document is the only legally binding version. Translated versions are not legally binding

2.2 Supported FormatsThe table below summarizes all supported inputs and outputs available on the S2H-30.Supported Input(s) Supported Output(s)SD-SDI

3 S2H-30 OSD Menu System OverviewThe S2H-30 is configured using the IR remote control to access the menu system through the OSD (see Section 4). Or,

3.2 Output MenuThe Output menu can be used to set up the output parameters. See table below for more information.Sub-Menu Value DescriptionInterfaceH

Sub-Menu Value DescriptionDVI Frequency23.98242529.973047.95485059.9460Match inputMatch Input x2 Set the DVI output frequency. This list shows all pos

3.3 Image MenuThe Image menu can be used to set up the image parameters.Sub-Menu Value DescriptionBrightness 0% to 100% Brightness value settingContr

3.4 Sync MenuThe Sync menu can be used to set up the sync parameters.Sub-Menu Value DescriptionInputSDISync input is set to SDI by default. It is th

3.5 Audio MenuThe Audio menu can be used to set up the audio parameters.Sub-Menu Value DescriptionInputSDIAudio input is set to SDI by default. It is

3.6 On Screen Display (OSD) MenuThe OSD menu can be used to set up the OSD parameters.Sub-Menu Value DescriptionOSD Enable YesNoEnable or disable On

3.7 System MenuThe System menu allows access to the system parameters.Sub-Menu DescriptionSave Save current settings to flash. Select to Save, when t

4 Infrared Remote Controller The Menu System can be accessed using the IR controller in conjunction with the OSD. Pressing the Menu button will invok

Table Of Contents1 Introduction...

4.2 Remote Controller FunctionsRemote Control FunctionInput source selection Select SDI or PatternNote: The DVI-D/HDMI and DVI-A buttons are unused.“

4.3 Input Source Setting• To select the Input Source, press one of the buttons available in the Input Source field (see Figure 5).Figure 5: Input Sou

4.3.2 Setting the IR ChannelWhen using multiple S2H-30 units, you can avoid interference by pairing each unit to an individual remote. Assign each S2

5 Doremi Universal Interface Software (DUIS)5.1 DUIS Installation• To install the Doremi Universal Interface Software, follow the steps below:• Plug

Figure 10: ”Found New Hardware Wizard” Window Step 2• When the driver installation is complete, click on the “Finish” button (see Figure 11).Figure 11

Figure 12: Hardware Installation Warning WindowFigure 13: Hardware Installation Warning Window for Windows 7S2H.OM.001540.DRM Page 25 of

5.2 Doremi Universal Interface Software OverviewThe Doremi Universal Interface Software can control one or more S2H-30 devices connected to a worksta

• The “Settings” field located on the left part of the screen allows the user to manage the settings files. The “Settings” field is presented in Secti

• To delete a settings file present in the “Settings files” area, select it and click on the “Delete” button (see Figure 15).• To update the “Settings

5.4 Tabs Description5.4.1 Input TabThe Input tab is illustrated in Figure 14 and Figure 15. All parameters are explained earlier in this manual in S

Software License AgreementThe software license agreement can be found at the following location:http://www.doremilabs.com/support/proav-support/proav-

5.4.3 Image TabThe Image tab is illustrated below in Figure 17.Figure 17: S2H-30 Control Panel Image TabAll parameters are explained earlier in this

Figure 18: Gamma Correction Pop-Up WindowS2H.OM.001540.DRM Page 31 of 39 Version 1.4 Doremi LabsLoad File Radio ButtonFormula Editi

5.4.4 Sync I/O TabThe Sync I/O tab is illustrated below in Figure 19.Figure 19: S2H-30 Control Panel Sync I/O TabAll parameters are explained earlier

5.4.5 Audio TabThe Audio tab is illustrated below in Figure 20.Figure 20: S2H-30 Control Panel Audio TabAll parameters are explained earlier in this

5.4.6 OSD TabThe OSD tab is illustrated below in Figure 21.Figure 21: S2H-30 Control Panel OSD TabAll parameters are explained earlier in this manual

5.4.7 System TabThe System tab is illustrated below in Figure 22.Figure 22: S2H-30 Control Panel System TabThe parameters are explained earlier in th

• A window containing the logs will appear:Figure 23: Log Window• Select “Auto Update” from that window to see all messages (see Figure 23).S2H.OM.001

6 Firmware UpdateThe firmware can be updated through a USB using the DUIS. In case one of the files listed in the procedures below is missing, please

7 AcronymsTerm DefinitionDUIS Doremi Universal Interface SoftwareDVI Digital Visual InterfaceHDMI High-Definition Multimedia Interface HD-SDI High-De

8 Document Revision HistoryDate Version Description02/10/2011 1.0 First version.03/02/2011 1.1 New pictures added.07/26/2012 1.2 Logo and contact inf

WARNING THIS DEVICE MUST BE GROUNDED IMPORTANTPower requirements for electrical equipment vary from area to area. Please ensure that the S2H-30 m

Protecting Yourself and the S2H-30Never touch the AC plug with wet hands. Always disconnect the S2H-30 from the power supply by pulling on the plug,

C A U T I O NR I S K O F E L E C T R I C S H O C KD O N O T O P E N !C A U T I O N : T O R E D U C E T H E R I S K O F

1 Introduction1.1 PurposeThis document provides guidance on how to use the S2H-30 SDI to HDMI® converter that incorporates High-Definition Multimedi

2 S2H-30 Overview2.1 S2H-30 DescriptionThe S2H-30 is an SDI to HDMI format converter featuring SDI and HDMI connectors that allow for any SDI input

2.1.3 S2H-30 Rear PanelThe S2H-30 rear panel is illustrated below:Figure 3: S2H-30 Rear Panel ViewThe rear panel has the following connectors:Connect